# generated by Slic3r 1.2.9 on Tue May  9 07:53:57 2017

[filament:ABS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 100
first_layer_temperature = 220
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 220

[filament:Dobot 2.0 Vase]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 0
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 200

[filament:PLA 1.75mm]
bed_temperature = 40
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 50
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 200

[filament:PLA Formfutura]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 0
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
first_layer_bed_temperature = 50
first_layer_temperature = 210
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 210

[presets]
filament = PLA 1.75mm.ini
filament_1 = PLA 1.75mm
print = High 0.15mm.ini
printer = Flashforge Dual.ini

[print:Dobot 2.0 Vase]
avoid_crossing_perimeters = 0
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 5
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 5
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 120%
fill_angle = 45
fill_density = 0%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.35
first_layer_speed = 5
gap_fill_speed = 5
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 5
interface_shells = 0
layer_height = 0.2
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 5
perimeters = 1
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 10
skirt_height = 1
skirts = 2
small_perimeter_speed = 5
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 5
spiral_vase = 1
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 5
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 5
top_solid_layers = 0
travel_speed = 5

[print:High 0.15mm]
avoid_crossing_perimeters = 1
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.25
first_layer_speed = 40
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
layer_height = 0.15
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].g
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 100
xy_size_compensation = 0

[print:Hyper 0.08mm]
avoid_crossing_perimeters = 1
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.2
first_layer_speed = 40
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.08
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].g
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 4
travel_speed = 100
xy_size_compensation = 0

[print:Low 0.3mm]
avoid_crossing_perimeters = 1
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.4
first_layer_speed = 20
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
layer_height = 0.3
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].g
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 80
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 2
travel_speed = 120
xy_size_compensation = 0

[print:My Settings]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 40%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.4
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130

[print:Standard 0.2mm]
avoid_crossing_perimeters = 1
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 40
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 50
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].g
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 2
post_process = C:\Slic3r\Perl scripts\postscript1.pl
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 100
xy_size_compensation = 0

[printer:Dobot 2.0 Vase]
bed_shape = 0x0,200x0,200x200,0x200
end_gcode = M104 S0 ; turn off temperature\nM107\nG91\nG1E-3\nG1Z+3\nG1Y+50\nG90\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
retract_before_travel = 2
retract_layer_change = 0
retract_length = 8
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
start_gcode = M106\n
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0.1

[printer:Flashforge Dual]
bed_shape = -114x-75,114x-75,114x75,-114x75
before_layer_gcode = 
end_gcode = ;End Gcode\nM107;   Disable cooling fan\nM104 S0 T0;  Set Nozzle temperature of Right nozzle to zero\nM104 S0 T1;  Set Nozzle temperature of Left nozzle to zero\nM140 S0;   Turn bed heating off\nG162 Z;    Home positive for Z axis\nG28 X0 Y0;   Return X and Y to home position\nM132 X Y Z A B\nG91;   Set to relative positioning\nM18;   Disable stepper motors for all axes
extruder_offset = 0x0,0x0
gcode_flavor = makerware
layer_gcode = 
nozzle_diameter = 0.4,0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2,2
retract_layer_change = 1,1
retract_length = 2,2
retract_length_toolchange = 2,2
retract_lift = 2,2
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 30,30
start_gcode = M140 S[first_layer_bed_temperature];   Heat bed up to first layer temperature\nM104 S[first_layer_temperature_0] T0;   Set nozzle temperature of Right extruder to first layer temperature\nM104 S[first_layer_temperature_0] T1;   Set nozzle temperature of Left extruder to first layer temperature\nM107;   Fan off\nG90;   Absolute Programming\nG28;   Move to Home position \nM132 X Y Z A B;   Load current home position from EEPROM\nG1 Z50 F600;   Move bed down to allow safe movement of nozzles lo left front\nG1 X-110.5 Y-74 F6000;   Move nozzles to left front\nM7;   Wait For Platform to reach target temperature\nM6 T0;   Wait For Right nozzle to reach target temperature\nM6 T1;   Wait For Left nozzle to reach target temperature\n; M106 enable cooling fan\nM907 X100 Y100 Z40 A100 B100;   Set digital potentiometer value. A and B typically 100 for tough filament like ABS and 80 for brittle like PLA. A is Right B is Left.\nG1 Z0.6 F3300; Go to start height\nG4 P2000;   Dwell time\nG1 Z[first_layer_height] F7200.000;   Move to first layer height\nM108 T[current_extruder];   Tool change to current extruder   
toolchange_gcode = M108 T[next_extruder]
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0,0
z_offset = 0

[printer:Flashforge Left ABS]
bed_shape = -114x-75,114x-75,114x75,-114x75
before_layer_gcode = 
end_gcode = M107 ; disable cooling fan\nM104 S0 T1\nM140 S0 \nG1 Z140 F3300 \nG28 X0 Y0 \nM132 X Y Z A B \nG91 \nM18
extruder_offset = 0x0,0x0
gcode_flavor = makerware
layer_gcode = 
nozzle_diameter = 0.4,0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2,2
retract_layer_change = 1,1
retract_length = 1,1
retract_length_toolchange = 10,10
retract_lift = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 30,30
start_gcode = M140 S[first_layer_bed_temperature]; heat bed up to first layer temperature \nM104 S[first_layer_temperature_0] T1; set nozzle heater to first layer temperature \nG90; Absolute positioning \nG28; Move to Home position \nM132 X Y Z A B ; Load current home from EEPROM \nG1 Z100 F3300 ; Tray down, warm up... \nG1 X-110.5 Y-74 F6000 ; waiting position in front left \nM7; wait for the platform \nM6 T1; wait for the toolhead. 1 is the left head. \nM106; enable cooling fan\nM907 X100 Y100 Z40 A20 B100 ; power up the stepper motor current \n; Begin! \nG1 Z0.6 F3300 \nG4 P2000 ;dwell time\nM108 T1 ;tool change\nG1 Z[first_layer_height] F7200.000; move to first layer height  
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0,0
z_offset = 0

[printer:Flashforge Left PLA]
bed_shape = -114x-75,114x-75,114x75,-114x75
before_layer_gcode = 
end_gcode = M107 ; disable cooling fan\nM104 S0 T1\nM140 S0 \nG1 Z140 F3300 \nG28 X0 Y0 \nM132 X Y Z A B \nG91 \nM18
extruder_offset = 0x0,0x0
gcode_flavor = makerware
layer_gcode = 
nozzle_diameter = 0.4,0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2,2
retract_layer_change = 1,1
retract_length = 1,1
retract_length_toolchange = 10,10
retract_lift = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 30,30
start_gcode = M140 S[first_layer_bed_temperature]; heat bed up to first layer temperature \nM104 S[first_layer_temperature_0] T1; set nozzle heater to first layer temperature \nG90; Absolute positioning \nG28; Move to Home position \nM132 X Y Z A B ; Load current home from EEPROM \nG1 Z100 F3300 ; Tray down, warm up... \nG1 X-110.5 Y-74 F6000 ; waiting position in front left \nM7; wait for the platform \nM6 T1; wait for the toolhead. 1 is the left head. \nM106; enable cooling fan\nM907 X100 Y100 Z40 A20 B80 ; power up the stepper motor current \n; Begin! \nG1 Z0.6 F3300 \nG4 P2000 ;dwell time\nM108 T1 ;tool change\nG1 Z[first_layer_height] F7200.000; move to first layer height  
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0,0
z_offset = 0

[printer:Flashforge Right ABS]
bed_shape = -114x-75,114x-75,114x75,-114x75
before_layer_gcode = 
end_gcode = M107 ; disable cooling fan\nM104 S0 T0 \nM140 S0 \nG1 Z140 F3300 \nG28 X0 Y0 \nM132 X Y Z A B \nG91 \nM18
extruder_offset = 0x0,0x0
gcode_flavor = makerware
layer_gcode = 
nozzle_diameter = 0.4,0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2,2
retract_layer_change = 1,1
retract_length = 1,1
retract_length_toolchange = 10,10
retract_lift = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 30,30
start_gcode = M140 S[first_layer_bed_temperature]; heat bed up to first layer temperature \nM104 S[first_layer_temperature_0] T0; set nozzle heater to first layer temperature \nG90; Absolute positioning \nG28; Move to Home position \nM132 X Y Z A B ; Load current home from EEPROM \nG1 Z100 F3300 ; Tray down, warm up... \nG1 X-110.5 Y-74 F6000 ; waiting position in front left \nM7; wait for the platform \nM6 T0; wait for the toolhead. 0 is the right head. \nM106; enable cooling fan\nM907 X100 Y100 Z40 A100 B20 ; power up the stepper motor current \n; Begin! \nG1 Z0.6 F3300 \nG4 P2000 ;dwell time\nM108 T0 ;tool change\nG1 Z[first_layer_height] F7200.000; move to first layer height  
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0,0
z_offset = 0

[printer:Flashforge Right PLA]
bed_shape = -114x-75,114x-75,114x75,-114x75
before_layer_gcode = 
end_gcode = M107 ; disable cooling fan\nM104 S0 T0 \nM140 S0 \nG1 Z140 F3300 \nG28 X0 Y0 \nM132 X Y Z A B \nG91 \nM18
extruder_offset = 0x0,0x0
gcode_flavor = makerware
layer_gcode = 
nozzle_diameter = 0.4,0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 2,2
retract_layer_change = 1,1
retract_length = 1,1
retract_length_toolchange = 10,10
retract_lift = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 30,30
start_gcode = M140 S[first_layer_bed_temperature]; heat bed up to first layer temperature \nM104 S[first_layer_temperature_0] T0; set nozzle heater to first layer temperature \nG90; Absolute positioning \nG28; Move to Home position \nM132 X Y Z A B ; Load current home from EEPROM \nG1 Z100 F3300 ; Tray down, warm up... \nG1 X-110.5 Y-74 F6000 ; waiting position in front left \nM7; wait for the platform \nM6 T0; wait for the toolhead. 0 is the right head. \nM106; enable cooling fan\nM907 X100 Y100 Z40 A80 B20 ; power up the stepper motor current \n; Begin! \nG1 Z0.6 F3300 \nG4 P2000 ;dwell time\nM108 T0 ;tool change\nG1 Z[first_layer_height] F7200.000; move to first layer height  
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0,0
z_offset = 0

[printer:My Settings]
bed_shape = 0x0,228x0,228x150,0x150
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = makerware
layer_gcode = 
nozzle_diameter = 0.4
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[settings]
autocenter = 
mode = expert